Villa main entrances
Hinged or pivot entrance doors with multi-point locking and commercial-grade closers.
Doors & Windows
Aluminium Doors
Hinged, sliding, bi-folding and lift-and-slide aluminium door systems, cut and assembled in our workshop and installed by our own team — specified around how the opening is actually used.
- Hinged, sliding & bi-folding
- Thermally broken options
- Hardware sized to the leaf
Who this work is for
- Homeowners
- Villa contractors
- Architects
- Property managers
Aluminium Doors — project photograph required
Real Al Makan photography goes here. No stock imagery is used on this site.
In practice
The hardware decides how long a door lasts, not the profile
An aluminium door is used thousands of times a year. The profile carries the glass and takes the wind, but it is the hinges, rollers, tracks and locking gear that wear — and those are exactly where a cheap quotation economises quietly. A door that drops or binds after eighteen months has almost never suffered a frame failure. It has hardware that was never rated for the weight of the leaf it was asked to carry.
That matters more here than in a milder climate. A large glazed leaf on a villa terrace can weigh well over a hundred kilograms, it is opened and closed in 45°C heat, and fine dust gets into every track. Rollers rated close to the leaf weight will fail; rollers rated comfortably above it will not. Stainless components in a coastal position will outlast plated steel by years.
Configuration follows how the opening is used, not how it looks in the drawing. A hinged door seals best, because the leaf compresses against gaskets on all four sides — the right choice for a main entrance where air-tightness and security matter. Sliding doors take no swing space, which is why they dominate balconies and terraces, but a sliding leaf runs on brushes rather than compression seals, so it will never be as tight. Lift-and-slide systems solve that: the leaf lifts off its seals to move and drops onto them when closed, giving a sliding action with a hinged door’s seal. Bi-folding doors open a whole wall, at the cost of a stack of leaves parked to one side and considerably more hardware to maintain.
Thermal breaks matter on any elevation that takes direct sun. A polyamide strip between the inner and outer sections interrupts the heat path through the frame, which shows up as a frame that is not painful to touch in the afternoon and a room the air conditioning is not fighting all day.
A door that drops after eighteen months is not a frame failure. It is hardware that was never rated for the leaf.
Where it is used
Aluminium Doors — typical applications
The situations this work most often solves. If yours is not listed, it is still worth asking.
Terrace and balcony access
Sliding and lift-and-slide systems where swing space does not exist, with tracks detailed for drainage.
Living-space openings
Bi-folding and stacking systems that open a whole wall onto a garden or majlis.
Commercial and office doors
Heavier leaves with commercial closers, panic hardware and access control provision.
Service and utility doors
Louvred, solid-panel and half-glazed doors for plant rooms, stores and back-of-house.
Replacement and upgrades
Swapping corroded or single-glazed doors for thermally improved systems without rebuilding the opening.
Design possibilities
Options you can choose from
Finishes, configurations and specification choices available on this work. Samples can be provided before anything is committed.
Opening type
Hinged, pivot, sliding, lift-and-slide, bi-folding or stacking — chosen for swing space, seal and daily use.
Sightlines
Slim minimal-frame systems where the view matters, or heavier profiles where span and security dominate.
Finish
Powder coating in any RAL including metallics and textures, anodised silver, bronze or champagne, or wood-effect sublimation.
Glazing
Clear, tinted, reflective, low-E or laminated, single or double glazed depending on orientation and privacy.
Threshold
Standard upstand, low-profile or flush thresholds where level access matters — detailed with drainage.
Hardware
Lever, pull, or concealed handles in satin stainless, black, bronze or brass, with matching hinges and locks.
Why it matters
What you get
-
Sealed against dust
Multi-point compression and quality gaskets keep the fine dust that gets everywhere out of the room.
-
Made to the opening
Fabricated to a surveyed dimension, so packing and silicone are not doing structural work.
-
Hardware that holds
Hinges, rollers and locks sized above the leaf weight, not close to it.
-
Cooler rooms
Thermal breaks and the right glass coating cut solar gain, which shows directly on the cooling load.
Technical
Specification notes
- Systems
- Hinged, pivot, sliding, lift-and-slide, bi-folding and stacking, in standard or thermally broken profiles.
- Glazing
- Single glazing 5–12mm; insulated units typically 6-12-6 or 6-16-6, clear, tinted, reflective or low-E.
- Hardware
- Multi-point locks, heavy-duty hinges, tandem rollers and closers rated above the actual leaf weight.
- Gaskets and seals
- EPDM rather than cheaper alternatives, because EPDM holds elasticity under UV and heat.
- Thresholds
- Standard, low-profile and flush options, with drainage designed into the sill.
- Finishes
- Polyester powder coating, anodising, and wood-effect sublimation for external exposure.
Final specification is confirmed at survey, against the actual opening, exposure and use.
How we do it
Our process for aluminium doors
The steps specific to this work — not a generic checklist.
- 01
Survey the opening
Structural opening, finished floor level, plumb and available swing or stacking space measured properly.
- 02
Choose the configuration
Opening type decided by seal requirement, swing space and how the door will actually be used every day.
- 03
Specify glass and hardware
Glass build-up from orientation and privacy; hardware sized from the calculated leaf weight.
- 04
Fabricate and glaze
Cut, machined and assembled in our workshop, glazed and sealed so the unit arrives complete.
- 05
Install, adjust and hand over
Fixed, packed, levelled and sealed, then every leaf adjusted and every lock tested before we leave.
Get a price for aluminium doors
Send drawings, dimensions or a photograph of the space. For anything beyond a straightforward replacement we will arrange a survey, because measuring it ourselves is the only way to quote a price that will not move.
Questions
Aluminium Doors — frequently asked
Sliding, in almost every case — a hinged leaf needs swing space that terraces rarely have. If air-tightness matters as much as space, a lift-and-slide gives you a sliding action with a hinged door’s seal, because the leaf drops onto its gaskets when closed.
They are, but they have more moving parts than any other configuration, and fine dust in the tracks is the enemy. They need brushing out regularly. If the opening is used daily rather than occasionally, a large sliding system is often the more practical choice.
Usually. Send photographs of the frame profile, the glazing bead and the hardware, plus the leaf dimensions. Those three things normally identify the system family closely enough to match.
No. Thermal breaks interrupt heat flow between outside and inside — on an internal opening there is nothing to interrupt. We will tell you when it is not worth the money.
Heavier than most people expect, provided the track and rollers are specified for it. The limit in practice is usually the structure above the opening and how the glass will be lifted into place, not the door system.
Related work
Often needed alongside this
Aluminium Windows
Casement, sliding, tilt-and-turn and fixed windows in thermally broken or standard aluminium.
Explore service
Glass Sliding Doors
Top-hung, barn-style, cavity and stacking sliding glass door systems.
Explore service
Shop Front Glass & Aluminium
Retail glazing and entrance systems built for footfall, security and presentation.
Explore service
Tempered / Toughened Glass
Toughened safety glass cut, drilled and edge-worked to size, supplied loose or installed.
Explore service
Get in touch
Tell us about the job
Drawings, dimensions or just a photo of the space — whatever you have is enough to start.
- Call us +971 56 436 9675
- WhatsApp +971 56 436 9675
- Email almakan.uae@gmail.com
- Workshop & office Ajman Industrial Area 1, Ajman, United Arab Emirates
- Opening hours Open daily · 08:00 AM – 11:59 PM